Water soaking some of the most important documents in your household can be a real pain and this is most likely to occur during a flood or a hurricane. No matter what stage you are at in life, odds are good that you have some important papers that could make things difficult for you if you were to lose them. This can include bank papers, loan information, warranties on expensive electronics, birth certificates, insurance papers, and anything else that you might need should a legal situation arise. These are often the only copies that we have and in some cases, the only copies that exist of certain documents and safeguarding them and knowing how to go about restoring them is essential.
Unless the documents have been submerged in water for more than two days, there is no real reason for you to go into a panic when rescuing them. The main concern here is that mold will start to grow on them after a couple of days and this is a worst case scenario, because mold loves to eat paper. You need to get the most important documents out of the water first thing and do whatever you can to get the humidity in the home down. Adjust the thermostat to around 65 degrees and keep the house at about this temperature if you can.
Any standing water in your house needs to be gotten rid of as soon as possible. Opening windows and doors should help air circulate and speed up the drying process. This will not only help minimize water damage in the house, but also help prevent mold.
Remove documents from standing water carefully, since they can disintegrate in your hands if you do this incorrectly. Lay them out on a flat surface to dry and most of the time, they should be fine.
Sometimes, however, items that have been under water for a while need to be freeze dried. Wrap these items up in freezer paper and pack them into a box; like sized items should go with other like sized items. Books should be packed with books and loose papers with loose papers. Do a last check of the house and make sure that you have everything that you intend to have restored.
Put your contact information on the outside of the boxes and have them transported to the nearest freeze dry facility.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.floodingct.info
http://www.floodedbasementnj.info
Monday, October 1, 2007
Water Damage Prone Areas of the Bathroom
Water damage in the bathroom is some serious business, since it can lower the value of your home significantly if it is not taken care of and also since it causes the bathroom to be unattractive to you and the rest of your family. Structural problems are also a hazard, but in the beginning the damage will only be cosmetic. This is fortunate, since you will be able to notice that there is a problem long before it does any long lasting damage. There are a few things that you can do to watch for water damage occurring to one of the most important rooms in your home.
There are several different junctions of water in your bathroom and they need to be inspected regularly and thoroughly to detect the presence of water damage. These are the sink, toilet, bath tub, and shower.
The shower and bath tub can require some special maintenance and attention. The tiles around the tub may crack over time and if they are, you should replace them and note whether there is any missing grout between any of the tiles. This grout needs to be filled in to keep water from seeping underneath the tile and damaging the wood underneath. Cracked caulking around the joints where the tile meets the walls or the tub needs to be replaced, as well.
The sink should be looked at every time you do a bathroom inspection, as the plumbing underneath could possibly be leaking. The seals in the pipes should be replaced if they are found to be loose or cracked in any way.
The toilet is also a vulnerable area of the bathroom. Any signs of moisture on the floor around the base of the toilet should be paid close attention to and any cracked tile around the base should be replaced. Toilets are notorious for overflowing due to clogs and one of the best ways to prevent this is to not put more toilet paper in it than it can handle at once. Hanging toilet bowl cleansers are also not advised, because these are likely to cause clogging.
Checking out the plumbing inside the walls can be difficult to do, but if you keep an eye out for signs of moisture on the walls and around the floor, you should be able to detect any leaks before they do any great amount of damage.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.floodingct.info
http://www.floodedbasementnj.info
There are several different junctions of water in your bathroom and they need to be inspected regularly and thoroughly to detect the presence of water damage. These are the sink, toilet, bath tub, and shower.
The shower and bath tub can require some special maintenance and attention. The tiles around the tub may crack over time and if they are, you should replace them and note whether there is any missing grout between any of the tiles. This grout needs to be filled in to keep water from seeping underneath the tile and damaging the wood underneath. Cracked caulking around the joints where the tile meets the walls or the tub needs to be replaced, as well.
The sink should be looked at every time you do a bathroom inspection, as the plumbing underneath could possibly be leaking. The seals in the pipes should be replaced if they are found to be loose or cracked in any way.
The toilet is also a vulnerable area of the bathroom. Any signs of moisture on the floor around the base of the toilet should be paid close attention to and any cracked tile around the base should be replaced. Toilets are notorious for overflowing due to clogs and one of the best ways to prevent this is to not put more toilet paper in it than it can handle at once. Hanging toilet bowl cleansers are also not advised, because these are likely to cause clogging.
Checking out the plumbing inside the walls can be difficult to do, but if you keep an eye out for signs of moisture on the walls and around the floor, you should be able to detect any leaks before they do any great amount of damage.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.floodingct.info
http://www.floodedbasementnj.info
Water Damage Prevention: Exhaust Fans
Keeping moisture out of your bathroom can be a big task, but installing an exhaust vent over the bath tub or the shower can be a tremendous help in this endeavor.
The purpose of the unit is to remove the steam from the bathroom so it does not become absorbed by the ceiling and walls in the bathroom and cause water damage. Mold growth is also a typical problem in the bathroom, so the exhaust fan will actually help you fight this second problem.
The quality of the fan is important. The quieter the fan’s operation, the higher the quality is. Some manufacturers do not put a noise rating on the packaging of the product, but most tend to do this to separate their high end exhaust fans from their basic ones. The other determining factor is how much air the exhaust fan will move per minute. The higher quality the fan, the more air it will remove from the room.
Ask yourself whether or not you want a light integrated into the fan unit. If so, then you might need a little bit of knowledge of how the electrical system in your house works. Purchasing a book on the subject is advised if you plan on installing the unit yourself.
If the fan is going to have a light in it, then it is a good idea to use the hole in your ceiling that should already exist from your original overhead light. If this does not exist or you want the fan separate from the light, you will create a hole with the jab saw. The electrical book you should have purchased should lay out the options on the kinds of switches you can use and how each one should be wired so you know you have continuity and that the wiring you install is correct.
After you are done wiring the fan, the exhaust duct kit will be installed next and this should come with instructions. This kit can be purchased at some hardware stores and home improvement stores.
Venting the air to the outside with the hose that came with the duct kit is not that difficult to do. Find the nearest soffit in your attic and cut a hole in it that follows the instructions that came with your duct kit. Attach the hose to it and you should be finished.
You will save a lot of money and time by installing this fan before water damage and mold becomes a problem in the bathroom. The damage caused by either can be quite extensive and expensive to repair.
Jim Corkern is a writer and promoter of quality
flood water damage restoration New Jersey and and other states such as
Connecticut Water Damage Restoration companies across the united states.
The purpose of the unit is to remove the steam from the bathroom so it does not become absorbed by the ceiling and walls in the bathroom and cause water damage. Mold growth is also a typical problem in the bathroom, so the exhaust fan will actually help you fight this second problem.
The quality of the fan is important. The quieter the fan’s operation, the higher the quality is. Some manufacturers do not put a noise rating on the packaging of the product, but most tend to do this to separate their high end exhaust fans from their basic ones. The other determining factor is how much air the exhaust fan will move per minute. The higher quality the fan, the more air it will remove from the room.
Ask yourself whether or not you want a light integrated into the fan unit. If so, then you might need a little bit of knowledge of how the electrical system in your house works. Purchasing a book on the subject is advised if you plan on installing the unit yourself.
If the fan is going to have a light in it, then it is a good idea to use the hole in your ceiling that should already exist from your original overhead light. If this does not exist or you want the fan separate from the light, you will create a hole with the jab saw. The electrical book you should have purchased should lay out the options on the kinds of switches you can use and how each one should be wired so you know you have continuity and that the wiring you install is correct.
After you are done wiring the fan, the exhaust duct kit will be installed next and this should come with instructions. This kit can be purchased at some hardware stores and home improvement stores.
Venting the air to the outside with the hose that came with the duct kit is not that difficult to do. Find the nearest soffit in your attic and cut a hole in it that follows the instructions that came with your duct kit. Attach the hose to it and you should be finished.
You will save a lot of money and time by installing this fan before water damage and mold becomes a problem in the bathroom. The damage caused by either can be quite extensive and expensive to repair.
Jim Corkern is a writer and promoter of quality
flood water damage restoration New Jersey and and other states such as
Connecticut Water Damage Restoration companies across the united states.
Standing Water, Water Damage, and Mold
Standing water inside of a home anywhere is a nuisance and most homeowners do not appreciate the liquid’s intrusion. It can happen almost anywhere, but most of the time the leaking of water into your house is completely preventable and the ability to repair it is always there.
Standing water not only causes water damage to the floor and walls, but it can also become a healthy breeding ground for mold. Stachybotrys atra is known for having a love of standing water and this is one of the last molds that you want growing in your house. While this mold is not as common as other genii of mold such as Cladosporium, Aspergillus, and Penicillium, it is not a rare one. It generally appears on items that have a high amount of cellulose content, such as dust, wood, paper on drywall, and etcetera. It requires almost constant moisture for days or weeks in order to start growing.
The health problems caused by Stachybotrys atra can be anything from coughing, runny noses, wheezing, and etcetera all the way to serious respiratory infections, rashes, and other serious health conditions.
Removing standing water from your home should be done as quickly as possible in order to prevent this mold growth and to prevent water damage. There are a few different causes of standing water.
If there is standing water in the basement after a heavy rain, then the cause could be that water is leaking into the basement through the foundation near the surface. This generally happens when water settles in around the base of the home in pockets because the soil is not piled high enough around the house. Water should not be allowed to settle around the house in this manner, so pile soil up around the foundation so that water runs down and away from it. Another good thing to do to keep this from happening is keeping your rain gutters cleared out as often as is necessary to keep them unclogged. Installing downspout extensions can also help run the water away from the home.
A cause of chronic standing water in the basement could be an underground spring leaking through the wall. There may not be much that you can do about this other than to have a drainage system installed. Do not assume that one type of drainage system fits all types of home constructions, because it does not. Talk to a contractor and find out what they recommend.
Jim Corkern is a writer and promoter of quality
South Carolina Water Damage Restoration and and other states such as
Chicago Water Damage Restoration companies across the united states.
Standing water not only causes water damage to the floor and walls, but it can also become a healthy breeding ground for mold. Stachybotrys atra is known for having a love of standing water and this is one of the last molds that you want growing in your house. While this mold is not as common as other genii of mold such as Cladosporium, Aspergillus, and Penicillium, it is not a rare one. It generally appears on items that have a high amount of cellulose content, such as dust, wood, paper on drywall, and etcetera. It requires almost constant moisture for days or weeks in order to start growing.
The health problems caused by Stachybotrys atra can be anything from coughing, runny noses, wheezing, and etcetera all the way to serious respiratory infections, rashes, and other serious health conditions.
Removing standing water from your home should be done as quickly as possible in order to prevent this mold growth and to prevent water damage. There are a few different causes of standing water.
If there is standing water in the basement after a heavy rain, then the cause could be that water is leaking into the basement through the foundation near the surface. This generally happens when water settles in around the base of the home in pockets because the soil is not piled high enough around the house. Water should not be allowed to settle around the house in this manner, so pile soil up around the foundation so that water runs down and away from it. Another good thing to do to keep this from happening is keeping your rain gutters cleared out as often as is necessary to keep them unclogged. Installing downspout extensions can also help run the water away from the home.
A cause of chronic standing water in the basement could be an underground spring leaking through the wall. There may not be much that you can do about this other than to have a drainage system installed. Do not assume that one type of drainage system fits all types of home constructions, because it does not. Talk to a contractor and find out what they recommend.
Jim Corkern is a writer and promoter of quality
South Carolina Water Damage Restoration and and other states such as
Chicago Water Damage Restoration companies across the united states.
Repairing Water Damaged Drywall
Water damaged ceilings can definitely be a safety hazard in your home, but not everyone has the money to hire a professional to repair or replace the section of drywall affected. It may just be a badly discolored piece of drywall or it could be that the tape between one section of drywall and another is sagging down. Even worse, the drywall could be weak in the middle and eventually collapse onto someone you care about. Something needs to be done about these water damaged areas of ceiling not only for structural purposes, but also for cosmetic ones, as well.
If the ceiling is only discolored badly with water stains, all you really should have to do is paint over it with primer first and then paint over that with the color of the rest of the ceiling. Your ceiling may be a traditional and ordinary white, but other colors will cover up the stains better, so consider this an opportunity to change the color of your ceiling. You will not have as much trouble covering up the stains with a paint that is not white.
No matter where the damaged piece of drywall is in your home, repairing it should be pretty easy. If it is the tape that is sagging down and coming apart from the drywall, all you need to do is remove the tape. Replace the tape and place joint compound over it. Smooth this out until the tape is not noticeable, paint over it with primer, then with the color of your ceiling.
If the drywall is sagging or cracked in the middle, then it needs to be completely replaced. You need to take out the entire damaged part of the drywall all the way to the joists, because the new piece of drywall needs something solid to hang onto or it will fall. It needs to be cut down the center of a joist in the ceiling so the new piece has something to rest on. Cut the new drywall to fit the part that you removed, screw it in with a drill, and tape over it the seam. Use joint compound over the tape and screws and smooth it out until the seams and screws are not noticeable anymore. Paint over it with primer the same way you would if you were only replacing the tape as mentioned earlier and then paint the color you desire back over it.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
mold remediation companies across the united states.
If the ceiling is only discolored badly with water stains, all you really should have to do is paint over it with primer first and then paint over that with the color of the rest of the ceiling. Your ceiling may be a traditional and ordinary white, but other colors will cover up the stains better, so consider this an opportunity to change the color of your ceiling. You will not have as much trouble covering up the stains with a paint that is not white.
No matter where the damaged piece of drywall is in your home, repairing it should be pretty easy. If it is the tape that is sagging down and coming apart from the drywall, all you need to do is remove the tape. Replace the tape and place joint compound over it. Smooth this out until the tape is not noticeable, paint over it with primer, then with the color of your ceiling.
If the drywall is sagging or cracked in the middle, then it needs to be completely replaced. You need to take out the entire damaged part of the drywall all the way to the joists, because the new piece of drywall needs something solid to hang onto or it will fall. It needs to be cut down the center of a joist in the ceiling so the new piece has something to rest on. Cut the new drywall to fit the part that you removed, screw it in with a drill, and tape over it the seam. Use joint compound over the tape and screws and smooth it out until the seams and screws are not noticeable anymore. Paint over it with primer the same way you would if you were only replacing the tape as mentioned earlier and then paint the color you desire back over it.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
mold remediation companies across the united states.
Subscribe to:
Posts (Atom)
