Water soaking some of the most important documents in your household can be a real pain and this is most likely to occur during a flood or a hurricane. No matter what stage you are at in life, odds are good that you have some important papers that could make things difficult for you if you were to lose them. This can include bank papers, loan information, warranties on expensive electronics, birth certificates, insurance papers, and anything else that you might need should a legal situation arise. These are often the only copies that we have and in some cases, the only copies that exist of certain documents and safeguarding them and knowing how to go about restoring them is essential.
Unless the documents have been submerged in water for more than two days, there is no real reason for you to go into a panic when rescuing them. The main concern here is that mold will start to grow on them after a couple of days and this is a worst case scenario, because mold loves to eat paper. You need to get the most important documents out of the water first thing and do whatever you can to get the humidity in the home down. Adjust the thermostat to around 65 degrees and keep the house at about this temperature if you can.
Any standing water in your house needs to be gotten rid of as soon as possible. Opening windows and doors should help air circulate and speed up the drying process. This will not only help minimize water damage in the house, but also help prevent mold.
Remove documents from standing water carefully, since they can disintegrate in your hands if you do this incorrectly. Lay them out on a flat surface to dry and most of the time, they should be fine.
Sometimes, however, items that have been under water for a while need to be freeze dried. Wrap these items up in freezer paper and pack them into a box; like sized items should go with other like sized items. Books should be packed with books and loose papers with loose papers. Do a last check of the house and make sure that you have everything that you intend to have restored.
Put your contact information on the outside of the boxes and have them transported to the nearest freeze dry facility.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.floodingct.info
http://www.floodedbasementnj.info
Monday, October 1, 2007
Water Damage Prone Areas of the Bathroom
Water damage in the bathroom is some serious business, since it can lower the value of your home significantly if it is not taken care of and also since it causes the bathroom to be unattractive to you and the rest of your family. Structural problems are also a hazard, but in the beginning the damage will only be cosmetic. This is fortunate, since you will be able to notice that there is a problem long before it does any long lasting damage. There are a few things that you can do to watch for water damage occurring to one of the most important rooms in your home.
There are several different junctions of water in your bathroom and they need to be inspected regularly and thoroughly to detect the presence of water damage. These are the sink, toilet, bath tub, and shower.
The shower and bath tub can require some special maintenance and attention. The tiles around the tub may crack over time and if they are, you should replace them and note whether there is any missing grout between any of the tiles. This grout needs to be filled in to keep water from seeping underneath the tile and damaging the wood underneath. Cracked caulking around the joints where the tile meets the walls or the tub needs to be replaced, as well.
The sink should be looked at every time you do a bathroom inspection, as the plumbing underneath could possibly be leaking. The seals in the pipes should be replaced if they are found to be loose or cracked in any way.
The toilet is also a vulnerable area of the bathroom. Any signs of moisture on the floor around the base of the toilet should be paid close attention to and any cracked tile around the base should be replaced. Toilets are notorious for overflowing due to clogs and one of the best ways to prevent this is to not put more toilet paper in it than it can handle at once. Hanging toilet bowl cleansers are also not advised, because these are likely to cause clogging.
Checking out the plumbing inside the walls can be difficult to do, but if you keep an eye out for signs of moisture on the walls and around the floor, you should be able to detect any leaks before they do any great amount of damage.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.floodingct.info
http://www.floodedbasementnj.info
There are several different junctions of water in your bathroom and they need to be inspected regularly and thoroughly to detect the presence of water damage. These are the sink, toilet, bath tub, and shower.
The shower and bath tub can require some special maintenance and attention. The tiles around the tub may crack over time and if they are, you should replace them and note whether there is any missing grout between any of the tiles. This grout needs to be filled in to keep water from seeping underneath the tile and damaging the wood underneath. Cracked caulking around the joints where the tile meets the walls or the tub needs to be replaced, as well.
The sink should be looked at every time you do a bathroom inspection, as the plumbing underneath could possibly be leaking. The seals in the pipes should be replaced if they are found to be loose or cracked in any way.
The toilet is also a vulnerable area of the bathroom. Any signs of moisture on the floor around the base of the toilet should be paid close attention to and any cracked tile around the base should be replaced. Toilets are notorious for overflowing due to clogs and one of the best ways to prevent this is to not put more toilet paper in it than it can handle at once. Hanging toilet bowl cleansers are also not advised, because these are likely to cause clogging.
Checking out the plumbing inside the walls can be difficult to do, but if you keep an eye out for signs of moisture on the walls and around the floor, you should be able to detect any leaks before they do any great amount of damage.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.floodingct.info
http://www.floodedbasementnj.info
Water Damage Prevention: Exhaust Fans
Keeping moisture out of your bathroom can be a big task, but installing an exhaust vent over the bath tub or the shower can be a tremendous help in this endeavor.
The purpose of the unit is to remove the steam from the bathroom so it does not become absorbed by the ceiling and walls in the bathroom and cause water damage. Mold growth is also a typical problem in the bathroom, so the exhaust fan will actually help you fight this second problem.
The quality of the fan is important. The quieter the fan’s operation, the higher the quality is. Some manufacturers do not put a noise rating on the packaging of the product, but most tend to do this to separate their high end exhaust fans from their basic ones. The other determining factor is how much air the exhaust fan will move per minute. The higher quality the fan, the more air it will remove from the room.
Ask yourself whether or not you want a light integrated into the fan unit. If so, then you might need a little bit of knowledge of how the electrical system in your house works. Purchasing a book on the subject is advised if you plan on installing the unit yourself.
If the fan is going to have a light in it, then it is a good idea to use the hole in your ceiling that should already exist from your original overhead light. If this does not exist or you want the fan separate from the light, you will create a hole with the jab saw. The electrical book you should have purchased should lay out the options on the kinds of switches you can use and how each one should be wired so you know you have continuity and that the wiring you install is correct.
After you are done wiring the fan, the exhaust duct kit will be installed next and this should come with instructions. This kit can be purchased at some hardware stores and home improvement stores.
Venting the air to the outside with the hose that came with the duct kit is not that difficult to do. Find the nearest soffit in your attic and cut a hole in it that follows the instructions that came with your duct kit. Attach the hose to it and you should be finished.
You will save a lot of money and time by installing this fan before water damage and mold becomes a problem in the bathroom. The damage caused by either can be quite extensive and expensive to repair.
Jim Corkern is a writer and promoter of quality
flood water damage restoration New Jersey and and other states such as
Connecticut Water Damage Restoration companies across the united states.
The purpose of the unit is to remove the steam from the bathroom so it does not become absorbed by the ceiling and walls in the bathroom and cause water damage. Mold growth is also a typical problem in the bathroom, so the exhaust fan will actually help you fight this second problem.
The quality of the fan is important. The quieter the fan’s operation, the higher the quality is. Some manufacturers do not put a noise rating on the packaging of the product, but most tend to do this to separate their high end exhaust fans from their basic ones. The other determining factor is how much air the exhaust fan will move per minute. The higher quality the fan, the more air it will remove from the room.
Ask yourself whether or not you want a light integrated into the fan unit. If so, then you might need a little bit of knowledge of how the electrical system in your house works. Purchasing a book on the subject is advised if you plan on installing the unit yourself.
If the fan is going to have a light in it, then it is a good idea to use the hole in your ceiling that should already exist from your original overhead light. If this does not exist or you want the fan separate from the light, you will create a hole with the jab saw. The electrical book you should have purchased should lay out the options on the kinds of switches you can use and how each one should be wired so you know you have continuity and that the wiring you install is correct.
After you are done wiring the fan, the exhaust duct kit will be installed next and this should come with instructions. This kit can be purchased at some hardware stores and home improvement stores.
Venting the air to the outside with the hose that came with the duct kit is not that difficult to do. Find the nearest soffit in your attic and cut a hole in it that follows the instructions that came with your duct kit. Attach the hose to it and you should be finished.
You will save a lot of money and time by installing this fan before water damage and mold becomes a problem in the bathroom. The damage caused by either can be quite extensive and expensive to repair.
Jim Corkern is a writer and promoter of quality
flood water damage restoration New Jersey and and other states such as
Connecticut Water Damage Restoration companies across the united states.
Subscribe to:
Posts (Atom)
